Remy Froissart, CNRS

Outils pour utilisateurs

Outils du site

Vous êtes ici: start » syncswap_guides_for_beginners » swaps_fees_and_safety
Piste:
syncswap_guides_for_beginners:swaps_fees_and_safety

Différences

Ci-dessous, les différences entre deux révisions de la page.

Lien vers cette vue comparative

— syncswap_guides_for_beginners:swaps_fees_and_safety [2026/03/08 14:57] (Version actuelle)
terrancexfq created
Ligne 1: Ligne 1:
 +
 +
 +
 +img  width: 750px;  iframe.movie  width: 750px; height: 450px; 
 +Syncswap multichain dex wallet setup and trading walkthrough
 +
 +
 +
 +Syncswap Multichain DEX Wallet Configuration and Asset Exchange Tutorial
 +
 +Install a browser extension like MetaMask; this software acts as your gateway. Create a new vault within it, meticulously recording the twelve-word recovery phrase on physical paper. Store this paper securely, separate from any internet-connected device. This sequence is non-negotiable for asset security.
 +
 +
 +Navigate to the protocol's interface. Select the "Connect" prompt, choosing your installed extension from the menu. Authorize the connection in the pop-up window from your vault software. You will now see your public address and network displayed on the platform.
 +
 +
 +Your vault likely holds Ether on Ethereum Mainnet. To engage with other networks like zkSync Era or Linea, you must bridge assets. Locate the "Bridge" section, specify the origin chain and destination, then confirm the transaction. Expect a delay of several minutes for finalization. Alternatively, use a centralized service to deposit funds directly onto a Layer 2.
 +
 +
 +For a token exchange, pick the desired pair and input an amount. The interface displays an estimated rate and fee. Slippage tolerance can be adjusted, typically between 0.5% and 1% for major pairs. Review the details, then execute the swap. Your vault will request confirmation; verify the parameters and gas fee before signing.
 +
 +
 +Monitor completed transactions in the platform's history tab. Each provides a link to a block explorer like Etherscan for immutable proof. For recurring actions, consider limit orders available on some integrated aggregators. Always verify you are on the correct network before any transaction to prevent fund loss.
 +
 +Syncswap Multichain DEX Wallet Setup and Trading Walkthrough
 +
 +Install a browser extension like MetaMask or Rabby, fund it with ETH for gas on its native chain, then bridge assets directly within the interface to zkSync Era using the native bridge for lowest fees or a third-party like Orbiter for speed.
 +
 +
 +Connect your funded extension to the platform.Navigate to the liquidity section and select a pair, e.g., ETH/USDC.Deposit an equivalent value of each asset; you'll receive LP tokens representing your share and earning fees.To exchange, go to the swap tab, pick tokens, review the quoted rate including the 0.3% protocol fee, and confirm the transaction in your extension.Monitor positions via your connected portfolio page, where you can also withdraw liquidity at any time.
 +
 +Installing and Connecting a Web3 Wallet for Syncswap
 +
 +Select MetaMask or Rabby for a first-time browser extension installation.
 +
 +
 +Visit the official Chrome Web Store or Firefox Add-ons page; never download from third-party links. Click "Add to Browser" and follow the prompts to create a new vault. Securely store the 12-word secret recovery phrase offline–this data controls your assets.
 +
 +
 +Network configuration is a mandatory step before interaction. Open your extension, navigate to network settings, and add the zkSync Era mainnet. Required details: Chain ID 324, RPC URL https://mainnet.era.zksync.io, currency symbol ETH.
 +
 +
 +Fund your newly created address. Use a centralized service to send ETH or USDC directly to your public address on the zkSync Era network. Bridging assets from Ethereum mainnet is another option, though it involves a delay.
 +
 +
 +Navigate to the protocol's interface.
 +
 +
 +Locate the connection button, typically in the top right corner. Your installed extension should appear in a modal window; select it and authorize the connection request. This grants the frontend permission to view your balance and propose transactions–it cannot move funds without your explicit approval for each operation.
 +
 +
 +Verify the connected network within the application's interface matches zkSync Era. A mismatch prevents functionality and risks failed transactions.
 +
 +
 +For repeated access, your connection persists. Clear browser data or use the extension's disconnect function to sever the link. Always review transaction details in the pop-up window, checking gas estimates and slippage tolerance before final confirmation.
 +
 +Q&A:
 +Is my wallet safe if I connect it to Syncswap?
 +
 +Syncswap is a decentralized application (dApp). This means it interacts with your wallet but does not hold or control your funds. Your assets remain in your self-custody wallet (like MetaMask). Safety primarily depends on your actions: only interact with the official Syncswap website, never share your seed phrase, and carefully review every transaction prompt before confirming. Be cautious of phishing sites that mimic the real dApp.
 +
 +What's the point of adding multiple networks to my wallet for Syncswap?
 +
 +[[https://sync-swap.com/index.php|SyncSwap token swaps]] operates across several blockchains, such as zkSync Era, Linea, and Scroll. Each network is separate. To trade assets native to Linea, your wallet must be connected to the Linea network. Adding these networks allows you to access liquidity and trade assets specific to each chain directly, without needing a separate bridge service for every transaction.
 +
 +I added a network but my funds aren't showing. Where is my ETH?
 +
 +Funds exist on a specific network. If you sent Ethereum (ETH) on the Arbitrum network but your wallet is currently set to the Optimism network, your balance will show as zero. Check your wallet's current selected network (often near the top of the extension) and switch it to the chain where you hold your assets. Your funds are safe on the blockchain; you're just viewing the wrong network.
 +
 +Can you explain what happens during a swap? The transaction details are confusing.
 +
 +When you approve a swap, you're sending two separate blockchain requests. The first is an 'Approve' transaction for the specific token you're spending. This grants the swap contract a one-time allowance to use that amount. The second is the 'Swap' transaction itself. This executes the trade via Syncswap's pools. You pay network (gas) fees for each step. Always check the expected output amount and maximum slippage you set before the final confirmation.
 +
 +Why did my swap fail and I still paid a fee?
 +
 +Failed transactions still require computational work from the network, so gas fees are charged. Common reasons for failure include setting slippage too low (price moved beyond your limit before confirmation), insufficient gas fee for the current network conditions, or insufficient liquidity for your trade size. Check transaction explorers like Etherscan for the specific error code after a failure.
  
syncswap_guides_for_beginners/swaps_fees_and_safety.txt · Dernière modification: 2026/03/08 14:57 de terrancexfq

Outils de la page

Sauf mention contraire, le contenu de ce wiki est placé sous les termes de la licence suivante : CC Attribution-Noncommercial-Share Alike 4.0 International
CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki